- 您现在的位置：买卖IC网 > Sheet目录303 > 844USB (B&K Precision)DEVICE PROGRAMMER USB INTERFACE
Device / Erase
This command allows erasing the whole programmable device. The program reports the end
without error or end with the error by writes the warning report on the display.
The Blank check procedure is applied after Chip erase command for such chips, where
doesn't exist other way how to check, the chip is really erased.
Device / Test
This command executes a test with device selected from list of supported devices (e.g. static
RAM) on programmers, which support this test.
Device / IC test
This command activates a test section for ICs separated by type to any libraries (on
distribution CD). First select an appropriate library, wished device and then a mode for test
vectors run (LOOP, SINGLE STEP). Control sequence and test results are displayed to LOG
WINDOW. In case of need is possible to define the test vectors directly by user. Detailed
description syntax and methods of creation testing vectors is described in example_e.lib file,
which is in programs installation folder.
Note.
Testing of IC is done using test vectors at some (pretty low) speed. The tests by test vectors
can not detect all defects of the chip. Other words, if IC test report "FAIL", then device is
defective. But if is "PASS" reported, it mean the chip passed our tests, but still might not pass
the tests, that check other - mainly dynamic - parameters of the tested IC.
Because the rising/falling edges of programmers are tuned for programming of chips, it may
happen the test of some chips fails, although the chips aren't defective (counters for
example).
Device / JAM/VME/...Player
Jam STAPL was created by Altera? engineers and is supported by a consortium of
programmable logic device (PLD) manufacturers, programming equipment makers, and test
equipment manufacturers.
The Jam? Standard Test and Programming Language (STAPL), JEDEC standard JESD-71,
is a standard file format for ISP (In-System Programming) purposes. Jam STAPL is a freely
licensable open standard. It supports programming or configuration of programmable devices
and testing of electronic systems, using the IEEE 1149.1 Joint Test Action Group (JTAG)
interface. Device can be programmed or verified, but Jam STAPL does not generally allow
other functions such as reading a device.
The Jam STAPL programming solution consists of two components: Jam Composer and Jam
Player.
The Jam Composer is a program, generally written by a programmable logic vendor, that
generates a Jam file (.jam) containing the user data and programming algorithm required to
program a design into a device.
The Jam Player is a program that reads the Jam file and applies vectors for programming and
testing of devices in a JTAG chain.
90
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
84702-0008
CONN RECEPT ETHERNET 8-8 PNL MNT
848A
MEMORY PROGRAMMER PARALLEL INTER
85506-0001
CONN MOD JACK VERT 8-8 HI-SPEED
85507-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-5001
CONN MOD JACK 8POS T/H HI SPEED
85511-0001
CONN MOD JACK VERT 8-8 HI-SPEED
862015-1
6 POS RECEPTACLE
相关代理商/技术参数
845
功能描述:程序设计器 - 基于通用和内存 REORD 615-865 UNIV. WITH SOFTWARE
RoHS:否 制造商:Xeltek 产品:Universal Device Programmers 工具用于评估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口类型:Parallel, USB 工作电源电压:90 VAC to 250 VAC
845 1 1/2"X15YD
功能描述:SCOTCH BOOK TAPE 845 1-1/2 IN X 制造商:3m 系列:* 零件状态:在售 标准包装:24
845 3"X15YD
功能描述:SCOTCH BOOK TAPE 845 3 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:12
845 4"X15YD
功能描述:SCOTCH BOOK TAPE 845 4 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:8
845 PRO4
制造商:Micro-Star International 功能描述:845 P4 S478 SDRAM LAN - Bulk
845 PRO4-L
制造商:Micro-Star International 功能描述:845 P4 SKT478 ATX SDRAM - Bulk
845 ULTRA
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk
845 ULTRA-DF
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk